91黄动漫 I 欧美 日韩 国产 成人 在线 I a级成人毛片 I 农村黄色片 I 男生捅女生的肌肌 I 精品99一区二区三区 I 妃光莉av I 日日夜夜操操 I 性中国古装videossex I 久久不卡av I 美女高潮动态图 I 极品美女开粉嫩精品 I 牛牛精品一区二区 I 91精品福利视频 I 成人刺激视频 I 91国内精品视频 I 中国一级特黄毛片大片 I 校长狠狠挺进校花体内小说 I 欧美激情黄色片 I 欧美久久久一区 I 爱豆国产剧免费观看大全剧苏畅 I 麻豆国产人妻欲求不满谁演的 I 亚洲一区二区在线免费观看视频 I 国产超碰av人人做人人爽 I 精品国产第一国产综合精品 I 久久免费看av I 欧美一区二区三区白人 I 国产精品夫妻激情 I 校花被肉干高h潮不断 I 欧美最猛黑人xxxx黑人表情 I 国产欧美日韩一区二区搜索 I 极品女神露脸呻吟啪啪 I 人人天天久久 I 亚洲动漫在线 I 日本91福利区 I 五月天 桃色 开心 I av在线免费观看国产 I 男人添女人的免费视频 I 夜夜穞天天穞狠狠穞

大家好！
不知大家有沒有使用過CP1L-EM40DT-D PLC 或者Ethernet通信模塊 CP1W-CIF41和CCD進行通信？這款PLC或通信模塊可否達到和CCD進行接收/發送數據的功能？
現在我有個項目使用到康耐視的CCD，支持Ethernet通信，康耐視相機關于通信協議的說明如下文：
   EtherNet/IP is an application level protocol implemented on top of the Ethernet TCP/IP and UDP/IP layers. It shares its object model with ControlNet and DeviceNet through the common Control and Information Protocol (CIP). This protocol allows the transfer of data and I/O over Ethernet.
      EtherNet/IP uses the standard Ethernet physical layer, and standard Ethernet and Internet protocols (TCP/IP, and UDP/IP) to transmit data. Because TCP/IP is a point-to-point topology, EtherNet/IP only uses this layer for explicit messaging; i.e. those messages in which the data field carries both protocol information and instructions for service performance. With explicit messaging, nodes must interpret each message, execute the requested task and generate responses. These types of messages are typically used to transmit configuration, diagnostic and event data.
     The UDP/IP protocol layer, which has the ability to multi-cast, is used for implicit messaging. With implicit messaging, the data field contains only real-time I/O data; no protocol information is sent because the meaning of the data is pre-defined at the time the connection is established, which in turn minimizes the processing time of the node during run-time. Implicit messages are short, occupying low-overhead, which allows for the time-critical performance needed by controllers.
**************************************************************************************************************************************************************************************************
因為CJ系列的PLC超出了費用預算，所以我想用CP1H或CP1L系列的PLC完成和相機之間的Ethernet通信！
不知可否？麻煩各位高手指點一下！
以上，謝謝!

CIF41模塊只能做從設備，也只接受Host Link協議
如果你的相機也是從設備，那就無法通訊。。。。。。